|
|
Manual versus orbital GTAW piping welding
Hofbauer, Jan ; Kubíček, Jaroslav (referee) ; Sigmund, Marian (advisor)
In thesis are compared options of stainless steel piping welding, orbital and manual version of method GTAW and GMAW. At the beginning, these methods are described theoretically and after that there are described materials used for fabrication two test welds on austenitic steel piping of diameter 168 mm. The first weld was made by orbital method GTAW, the second one by manual method GMAW. Next, these two welds are compared based on defects, welding parameters and width of heat affected area. The conclusion is that both welds are defect-free and because of economical aspects is better to use orbital GMAW method for this diameter of piping.
|
|
|
Compared HAZ the methods of welding TIG, MAG and CMT
Šoulák, Petr ; Sigmund, Marian (referee) ; Kubíček, Jaroslav (advisor)
The bachelor thesis was to compare the HAZ size for the TIG, MAG and CMT methods. The welded materials were low carbon steel and austenitic stainless steel. Samples of 250x50 mm size and 2 mm thick were welded with butt weld without a gap. In the first part of experiment, samples were welded at the same welding speed. The second part concerned only CMT, where the optimal welding speed was used. For selected samples, the HAZ size was measured and compared in macroscopic images.
|
|
|
Welding of high strenght steel by laser
Číp, Tomáš ; Kubíček, Jaroslav (referee) ; Mrňa, Libor (advisor)
This project, elaborated within the engineering studies (code of field of study: N2301), presents experiment of welding of high-strength steel by laser. In this project, the samples of high-strength steel DOMEX 420MC will be welded by laser welding method and the welded joints will then be compared with welds made by MAG method. The theoretical part of this project summarizes the following key words in individual chapters: lasers, technology of welding of steel using laser, welding by MAG method, steel with higher strength, types of defects and check of welded joints. The practical part contains description of and assessment of mechanical tests of welded joints – weld bending test and transverse tension test. Further on, the tests of macrostructure and microstructure of welded joints were conducted and assessed. Final results of whole experiment are reviewed at the end of my diploma thesis.
|
|
|
Laser welding of the abrasive steel
Sklenář, Zdeněk ; Daněk, Ladislav (referee) ; Mrňa, Libor (advisor)
The project, prepared by the engineering study compares the welding abrasive steel HARDOX 400, fiber laser welding method, which will be compared with a MAG welding method and using different protective gases (argon and helium). In the theoretical part, i worked both welding technology's and the issue of high-strength steel. In the experimental part were performed and evaluated by destructive mechanical testing and bending test, the transverse tension test, test macrostructure and microstructure of welds. In conclusion the thesis deduced the final results of the experiment.
|
|
|
Economy comparison of welding technology MAG and ESAB-SAT
Lžičař, David ; Martinec, Jiří (referee) ; Kubíček, Jaroslav (advisor)
This project, elaborated in terms of Master’s studies in domain 2303T005 presents an analysis comparing conventional method of welding MAG and welding technology ESAB SAT^TM. ESAB SAT^TM is the new innovative method based on the principle of welding by the method MAG. The experimental part of the project is aimed to assessing the quality of welded joints, produced by ESAB SAT^TM, which part is performing selected destructive tests. Afterwards economic analysis by comparative method evaluates the measured and calculated parameters of welding.
|
|
|
Welding of reinforcing steel bars
Bogar, Radek ; Geryk, Pavel (referee) ; Kubíček, Jaroslav (advisor)
Radek Bogar: Welding of reinforcing steel bars Bachelor's degree Bachelor thesis, 2010/2011, FSI VUT Brno, Institute of Engineering Technology, Department of welding and surface treatment, a course in B-STI Mechanical Engineering degree program B3S-P Engineering, May 2011 str. 49, obr. 42, tab. 12, annex 2. This thesis, developed in an undergraduate degree in mechanical engineering, is focused on the manufacture and welding of reinforcing steel bars, especially for individual types of structural welds, welding methods to be used, production testing and evaluation. The work consists of literary studies of the theoretical foundations of the production of concrete and welding steel bars, their design and use for purposes of concrete structures. Part of this work is the suggestion of additional material and WPS.
|
|
|
Modern welding processes for pressure vessels
Sýkora, Jan ; Janík, Martin (referee) ; Kubíček, Jaroslav (advisor)
This paper deals with modern methods of welding pressure tanks. The aim of this bachelor paper is to describe individual methods assigned to welding pressure tanks. Foremost, different methods of welding are listed followed by procedure description of pressure tank production and lastly specification of welding procedure for individual welds is described.
|
|
|
Progress of welding in shipbuilding
Urban, Václav ; Kubíček, Jaroslav (referee) ; Kovář, Petr (advisor)
This work deals with the methods of welding in shipbuilding, summarises the basic techniques used for welding of the SAW, MAG, MIG, TIG, laser, Laser-Hybrid. It describes the properties of welded material. Especially the materials HY80 and HY100. It follows from the filler materials. In particular materials Spoolarc 95 and 120. Particular emphasis is placed on the method of Laser-Hybrid, its properties and use in shipbuilding. Finally, describes the method of welding aluminium using FSW, preparation of welded surfaces and producting of sandwich panels.
|
|
|
Design of flat pallet for automatic parking garage
Osmík, Jiří ; Mrňa, Libor (referee) ; Kubíček, Jaroslav (advisor)
Design of flat pallet for automatic parking garage. Parking and description of automatic parking systems. Welding and weldability of materials. Electric arc welding and welding by melting electrode in protective gas by MIG/MAG method, welding instruments. Design of parking palette calculation and calculation this palette by MKP method. Process of drawing documentation for parking palette. Design of welding process and WPS. Description of annealing and zinc coating. Economic-technical analysis of palette for automatic parking system production.
|
|
|
Certification of company according to ČSN EN 15085 and ČSN EN ISO 3834
Kazdera, Tomáš ; Daněk, Ladislav (referee) ; Kubíček, Jaroslav (advisor)
The project elaborated in frame of engineering studies is focused on the certification of the company SW-MOTECH sro in the welding of steel structures for rail vehicles. According to standards ČSN EN 15085 and ČSN EN ISO 3834. The first part focuses on theoretical introduction to the used welding methods. The second section describes the destructive and non-destructive tests on individual welding methods, including their evaluation. Based on work tests pWPS is exposed to welding procedure WPS
|
guest ::
